Beginner’s Guide to Wet Felting

Final product image
Yellow layer in opposite direction
Add another one to three layers of roving
Add designs to the top layer
place the nettingtulle over the top of your project

What You’ll Be Creating

Wet felting wool is a centuries old craft used to make everything from tents to clothing. This tutorial will teach you the basics of how to felt wool roving into a beautiful piece of fiber art.

Felting supplies

For this project you’ll need:

  • a sheet of bubble wrap, larger than the size of your project
  • a towel, larger than the size of your project
  • netting or tulle, larger than the size of your project
  • assorted colors of wool roving
  • a spray bottle
  • a large wooden dowel, rolling pin, or piece of firm pool noodle
  • soap
  • two elastic pieces
Towel with bubble wrap on top
Lay out your towel and bubble wrap, bubble side up

Lay out your towel and bubble wrap, bubble side up, on a water-safe work surface.

pull your roving into drafts
gently pull your roving into “drafts”.

Next, gently pull your roving into “drafts”. Pulling lightly will give nice 10-15 cm (4-6 inch) long pieces.

Layer of red wool roving on bubble wrap
Lay each draft in the same direction for the first layer

Arrange each draft on the bubble wrap. Lay each draft in the same direction for the first layer. Try to make the layer as even as possible, filling in thin areas with drafts of wool.

The next layer should be laid in the opposite direction. Make this layer even and consistent as well.

Add another one to three layers of roving, alternating fiber directions.

Once you have completed layering the drafts of roving, you can add any design elements or embellishments to the top layer.

Carefully place the netting/tulle over the top of your project, making sure not to displace any of the designs you have made or the structure of the roving layers. 

Spray the mixture on the wool
Spray the mixture on the wool

Fill the spray bottle with hot water and liquid soap. Use plenty of soap, so that the water is quite sudsy. The exact amount will vary depending on the volume of water and the type of soap.

Spray the mixture on the wool. Thoroughly wet the wool, but try to avoid using so much water that it begins to pool. If you add too much water, just carefully blot the excess water with a towel.

gently start rubbing the your hands over the project
gently start rubbing the your hands over the project

Once the wool has been sprayed, gently start rubbing the your hands over the project. You will notice that soap begins to foam as you rub. Continue to rub for at least 7 to 10 minutes. This rubbing will begin the felting process.

roll the project up around the rolling pin
Carefully begin to roll the project up around the roller

Once you have rubbed your project, place the wooden dowel/rolling pin/foam noodle at one end of the towel. Carefully begin to roll the project up around the item you are using. Continue rolling until the whole towel and project are around the tool.

Rolled up project with ties around it
Tie elastic pieces and tie them securely around the rolled up project

Take the elastic pieces and tie them securely around the rolled up project.

rolling the whole parcel back and forth
Roll in long, firm but gentle strokes an equal number of times in each direction going round the clock

Once the ties are in place, begin rolling the whole parcel back and forth. Make sure to roll in long strokes so that the whole parcel is evenly rolled.

Gently pinch the topthis is called a pinch test
A pinch test. If fibers pull up, your project has not felted enough. Roll up and repeat 100 times in each direction.

After rolling for 10 to 12 minutes, untie and unroll the towel. Carefully lift the netting from the top of the wool. Gently pinch the top—this is called a pinch test. If fibers pull up, your project has not felted enough. 

Rotate the piece 90 degrees and repeat steps 3 to 5 again. Try the pinch test again. If very few fibers pull up, your felting is complete on this side. 

Turn the wool over and repeat steps 3 to 6 for the back side of the project.

Once both sides have been rolled, peel the wool off both the bubble wrap and netting. Fold into quarters or thirds.

Prepare two bowls, one with very cold water and one with hot water. Place the folded wool into the hot water.

Remove the wool from the hot water after a few seconds, gently squeeze the water out, and then place the wool into the cold water. Allow it to set in the cold water for a few seconds and then gently squeeze the cold water out. Repeat these alternating hot and cold dunks four or five times. 

Make sure that all the soap is rinsed from the wool. The hot and cold water might need to be changed if too much soap builds up in them.

Once the wool is completely rinsed, lay the finished felted wool out to air dry. You have just completed your first wet felted wool piece!

Same process on the back side

Envato Tuts+ tutorials are translated into other languages by our community members—you can be involved too!Translate this post

29,026Tutorials1,285Courses43,093Translations

© 2020 Envato Pty Ltd. Trademarks and brands are the property of their respective owners.

https://consentcdn.cookiebot.com/sdk/bc.min.html

Published by Felting in Devon

Felt artist, Fibre artist, Wet Felter, Nuno Felter, Felting in Devon workshops,

2 thoughts on “Beginner’s Guide to Wet Felting

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Create your website at WordPress.com
Get started
%d bloggers like this: